800-827-1333 or 805-683-1196 info@candmtopline.com

Free Shipping! No Tax Outside of CA!

Rotary Tumbler Barrels

Tumbling Barrels

All of our tumbler barrel bases include the following features:

  • Rotational molded HDPE
  • High strength with long life
  • stainless steel barrel plug
  • Economically priced
  • Can be used on other machines
  • Used for wet or dry tumbling
  • Always in stock, same day shipping
  • MADE IN THE USA

Shipping included anywhere in the 48 states!

Rotary Barrel Tumbler Applications

Tumbling barrels work well on small parts. They are commonly used to finish screw machine parts, jewelry, and medical parts. They can also be used to mix dry or wet chemicals. The barrels and barrel plugs are impervious to most all chemicals. It is easy to retrieve the parts from the barrel by using a separation screen over a container. They also work well for burnishing brass, copper, aluminum and stainless with porcelain or steel media. Burnishing can also be done with dry media like cob or nut shell that has rouge baked on it. Steel ball burnishing can be done in a tumbling barrel at a very low cost.

NOTE: Our Specialty T-1 MDT/IOL Barrel is not pictured on this page. See IOL Finishing Equipment for more information and ordering details.

TL-1 Tumbler Barrel, 22 fl. oz.

5″ diameter X 4 1/2″ in length with 3″ opening

This barrel is for our THREE BAR tumbling, but is also used on other machines. As many as 8 barrels fit on our machine.

Barrel RPM on the Topline Tumbling barrel base.

When machine is set on HIGH speed barrel turns at 44 RPM.

When machine is set on LOW speed barrel turns at 29 RPM.

$59.00

Add to cart

MADE IN THE USA

TL-2 Tumbler Barrel, 3.5 qts

8 1/4″ diameter X 5 1/2″ in length with 4″ opening

This barrel is for our TWO BAR tumbling barrel base. As many as 4 of these barrels fit on our machine.

Barrel RPM on the Topline Tumbling barrel base.

When machine is set on HIGH speed barrel turns at 54 RPM.

When machine is set on LOW speed barrel turns at 36 RPM.

$94.00

Add to cart

MADE IN THE USA

TL-3 Tumbler Barrel, 1.5 gal

10 1/2″ diameter X  7″ in length with 4″ opening

This barrel is for our TWO BAR tumbling barrel base. As many as 3 of these barrels fit on our machine.

Barrel RPM on the Topline Tumbling barrel base.

When machine is set on HIGH speed barrel turns at 43 RPM.

When machine is set on LOW speed barrel turns at 29 RPM.

$119.00

Add to cart

MADE IN THE USA

TL-4 Tumbler Barrel, 2.5 gal

10 3/4″ diameter X  10 1/2″ in length with 4″ opening

This barrel is for our TWO BAR tumbling barrel base. As many as 2 of these barrels fit on our machine.

Barrel RPM on the Topline Tumbling barrel base.

When machine is set on HIGH speed barrel turns at 40 RPM.

When machine is set on LOW speed barrel turns at 25 RPM.

$149.00

Add to cart

MADE IN THE USA

TL-6 Tumbler Barrel, 8 gal

16″ diameter X  15″ in length with 7 1/4″ opening

This barrel is for our TWO BAR tumbling barrel base. One of these barrels fit on our machine.

Barrel RPM on the Topline Tumbling barrel base.

When machine is set on HIGH speed barrel turns at 27 RPM.

When machine is set on LOW speed barrel turns at 18 RPM.

$259.00

Add to cart

MADE IN THE USA

Replacement Tumbler Barrel Covers

All our covers are made with a spun stainless steel plate inside and outside. The seal is made with a large rubber ring sandwiched between the two plates. There is a stainless carriage bolt that goes through the top and a wing nut on the outside that is tightened to make the seal.

Our design allows the top to be removed and replaced quickly and easily. These tops may be purchased separately for replacement in our barrels.

3" Cover

(for TL-1)

$28.00

Add to cart

4" Cover

(for TL-2, TL-3, TL-4)

$34.00

Add to cart

7 1/4" Cover

(for TL-6)

$79.00

Add to cart